HydraMaster CDS 4.6 Скачать руководство пользователя страница 120

Страница: 120 / 126

10-7: Machine Maintenance

Troubleshooting

HEATINg SYSTEM

1.0. Vehicle overheats and shuts off CDS

Refer to vehicle dealer for diagnosis and repair.

2.0. Vehicle overheats

2.1. faulty thermostat in

vehicle.

Refer to dealer

2.2. faulty water pump on

vehicle

Refer to dealer

2.3. faulty radiator (plugged)

limited water flow

Refer to dealer

2.4. faulty fan clutch, limited

air-flow.

Refer to dealer

3.0. Unable to achieve normal cleaning temperature

3.1.There is hard water or

chemical build-up in the heat

exchangers.

This will not allow the heat to transfer properly. Descale

and flush as necessary.

3.2. Cleaning solution flow is

too great.

Measure flow at tool.

3.2.1. The jet in the cleaning tool is too large or worn out.

Test the tool for water flow and replace or repair jet as

necessary.
3.2.2. Cleaning solution pressure is too high. Adjust

pressure to normal. Inspect pressure gauge for accurate

reading.

3.3. The system thermal

valve is stuck open.

Remove recovery tank lid and check for premature flow

from thermal valve hose at tank. The machine must be

at or below normal operating temperature for this test.

Replace or repair as necessary.

3.4. The CDS is being

operated at too low rpm or

too low vacuum setting.

The system must be at full operating rpm and full vacuum

load to achieve full operating temperature. These values

must be set per manufacture’s specifications. Adjust

vacuum or rpm as necessary.

Содержание CDS 4.6































































































































Результаты поиска

Содержание CDS 4.6

Отзывы:

HydraMaster CDS 4.6, Руководство пользователя, Страница: 120 / 126

Результаты поиска

Содержание CDS 4.6

Отзывы: