HydraMaster CDS 4.6 Скачать руководство пользователя

Страница: 106 / 126

Vacuum Blower System: 8-2

To protect the vacuum blower from overloading and damaging itself, there is a vacuum

relief system installed on the vacuum recovery tank. When the vacuum tank inlet is

completely sealed off, a maximum of 14” Hg will be attained. At the end of each day,

spray an oil-based lubricant into the blower lubrication port before shutting down the

machine. If you fail to lubricate the vacuum blower on a daily basis, rust deposits and

moisture can form and decrease the life of the vacuum blower.

foam passing through the blower could lead to serious problems. Therefore, it is

important to keep the vacuum tank foam free. When cleaning surfaces with excessive

foaming residue, use HydraMaster’s Defoamer as directed.

The vacuum tank is protected from excessive water level overflowing by a vacuum tank

float kill switch. The switch is not activated by foam, only by liquid.

VACUUM TANK INLET FILTER

HydraMaster inlet filter screens are designed to trap lint, hair and large objects that would

normally collect at the bottom of your vacuum tank. Clean the screen at the end of each

job to eliminate build-up of debris in the tank.

VACUUM BLOWER LUBRICATION

Read the vacuum blower owner’s Manual, included with the CDS 4.8 / 4.6 owner’s

Manual, for proper oil changing instructions. Because the CDS is very demanding of

the vacuum blower, the vacuum blower should be maintained as recommended in the

vacuum blower owner’s Manual.

Remember to:

Remove vented oil fill plug on front or rear oil case.

Fill with specified oil until it registers to the top of the sight glass.

use lubricants as listed in the Table 8-1.

Add fresh oil as required to maintain proper level.

The oil should be drained, flushed and replaced every 300 hours. The oil drain hose is

connected under the head plate; at the end of the oil drain hose is a cap.

Содержание CDS 4.6































































































































Результаты поиска

Содержание CDS 4.6

Отзывы:

Похожие инструкции для CDS 4.6

Бренды по названию

Популярные бренды

HydraMaster CDS 4.6, Руководство пользователя

Результаты поиска

Содержание CDS 4.6

Отзывы:

Похожие инструкции для CDS 4.6

Бренды по названию

Популярные бренды