manualshive.com logo in svg

HydraMaster CDS 4.6, Руководство пользователя, Страница: 107 / 126

Поделиться
Скачать
HydraMaster CDS 4.6 Скачать руководство пользователя страница 107

8-3:   Vacuum Blower System

Vacuum Blower Troubleshooting

1.0. Weak vacuum at tool/wand.

gauge reads normal (10” Hg to 14” Hg)

1.1. Clogged hoses or tool/

wand tube.

Disconnect hoses and carefully check for an obstruction.

1.2. excessive length 

of hoses connected to 

machine.

Make sure machine is rated for the conditions under 

which it is being operated.

2.0. Vacuum gauge will not come up to 14” Hg

2.1.There is an air leak 

somewhere in the vacuum 

system.

Check vacuum relief valve for proper adjustment.  

Check all hoses for cuts and breaks.  Check recovery 

tank lid gasket. Make sure the recovery tank drain valve 

is fully closed.

2.2. The vacuum gauge is 

defective.

Test and replace as necessary.

2.3.Vacuum blower is 

turning too slowly.

Check  blower  rpm  at  tachometer  on  the  CDS’  dash. 

Blower rpm should be 2 times the tachometer rpm. See the 

throttle control kit instructions for further troubleshooting 

assistance.

3.0. Vacuum gauge reads high with no hoses attached

3.1.filter in recovery tank is 

clogged.

Remove and clean or replace as necessary.

3.2. Hose from recovery 

tank to blower is collapsed 

internally

Inspect and replace as necessary.

Lubricants for Oil-Lubricated gears and Bearings

Table 8-1.  

Ambient Temperature*

Oil grade USA

Oil Viscosity,

Centistokes at 40

°

Below 32° f (0° C)

SAe 20 Non-Detergent

100

32° to 100° f (0° to 38° C)

SAe 40 Non-Detergent

200

over 100° f (38° C)

SAe 50 Non-Detergent

250

*Refers to ambient air temperature at the cleaning tool

In applications with extreme variations in ambient temperature, a 20W - 50W multiple 

viscosity oil is recommended.

Содержание CDS 4.6































































































































Отзывы:

Нет отзывов