background image

Ultra Low Front

 

 

Rear Load

  

Excel

P/N 0501930_G 

5-3

HUSSMANN CORPORATION • BRIDGETON, MO  63044-2483  U.S.A.

Ultra Low Front

 

 

Rear Load

  

Excel

HUSSMANN CORPORATION • BRIDGETON, MO  63044-2483  U.S.A.

CLEANING DOOR TRACKS

The bi-fold door mechanism is contained in 
tracks at the top and bottom of each door . To 
ensure optimum operation, the tracks must be 
kept clear of debris at all times .

1 .  Do not allow liquids to collect in the 

tracks .

2 .  Clean tracks at least weekly:

 

• Remove door bumpers from tracks to 
ensure complete cleaning .

 

• Use track wipe-outs, located at the center 
of each track, when cleaning .

 

• Use soap and hot water with a brush to 
remove accumulated debris .

3 .  If necessary, the bi-fold 

doors may be opened 
fully . Pull the upper and 
lower pins to release 
center doors from track . 
Be sure to seat the pins 
fully when returning the 
door to the track .

4 .  Replace door bumpers 

after cleaning .

5 .  Do not add lubricant to 

the door mechanism .

{

Track

Track

Bumper (remove)

Wipe Out

Open Doors 

Remove Door 

Bumper

Track

Track

Track Wipe-out

Detail — Pull Pins to Release Doors 

From Track

Pull Center Pins to 

Release From Track

Содержание 0501930_G















































Отзывы: