Husqvarna , LZ6130TXPKOA Скачать руководство пользователя

Страница: 47 / 84

English-

MAINTENANCE

Checking Tire Pressures

All four tires should have a pressure of 15 psi
/ 103 kPa / 1 bar.

Checking the Parking Brake

Visually check that no damage is found on
the lever, links, or switch belonging to the
parking brake. Perform a test drive and check
that there is sufficent braking action.

To adjust the parking brake, contact the
Husqvarna service workshop.

Checking the V-belts

Deck belt

Check every 100 hours of operation. Check
for severe cracking and large nicks.

NOTE: The belt will show some small cracks
in normal operation.

To replace belt lower the deck to its lowest
position. Remove the foot plate and belt
shields.

Use a ratchet with a 9/16” socket on the
spring idler bolt to relieve the tension on the
belt. Slide the belt off of pulley and remove
the belt.

Reverse the proceedure for installation. See
the decal on the top of deck for belt routing
information.

After installation is complete check the belt
for twists.

8011-564

Tire pressures

8011-511-1

The parking brake in the disengaged position

WARNING!
Faulty adjustment can cause
an accident.

8011-622

Slackening the belt tensioner

8011-580

Belt routing, deck belt

Содержание , LZ6130TXPKOA





















































































Результаты поиска

Содержание , LZ6130TXPKOA

Отзывы:

Похожие инструкции для , LZ6130TXPKOA

Бренды по названию

Популярные бренды

Husqvarna , LZ6130TXPKOA, Руководство оператора

Результаты поиска

Содержание , LZ6130TXPKOA

Отзывы:

Похожие инструкции для , LZ6130TXPKOA

Бренды по названию

Популярные бренды