Husqvarna , LZ6130TXPKOA Скачать руководство пользователя | Manualshive

Страница: 40 / 84

background image

English-

38

MAINTENANCE

9.

Connect BLACK grounding cable to
negative (-) battery terminal with
remaining hex bolt and hex nut.

10. Fit the terminal guard.

11. Lower seat.

Ignition System

The engine is equipped with an electronic
ignition system. Only the spark plugs require
maintenance.

For recommended spark plugs, see Technical
Data.

1.

Remove the ignition cable boot and
clean around the spark plug.

2.

Remove the spark plug with a spark plug
socket wrench.

3.

Check the spark plug. Replace the spark
plug if fouled, the electrodes are burned
and if the insulation is cracked or
damaged. Clean the spark plug with a
steel brush if it is to be reused.

4.

Measure the electrode gap with a
gapping tool. The gap should be .030”
(0.75 mm). Adjust as necessary by
bending the side electrode.

5.

Reinsert the spark plug, turning by hand
to avoid damaging the threads.

6.

After the spark plug is seated, tighten it
using a spark plug wrench so that the
washer is compressed. A used spark
plug should be turned 1/8 of a turn from
the seated position. A new spark plug
should be turned 1/4 a turn from the
seated position.

7.

Replace the ignition cable.

IMPORTANT INFORMATION
Fitting the wrong spark plug type can
damage the engine.
Inadequately tightened spark plugs can
cause overheating and damage the
engine. Tightening the spark plugs too
hard can damage the threads in the
cylinder head.

8011-054

Measure the electrode gap

«
...
38
39
40
41
42
...
»

Содержание , LZ6130TXPKOA





















































































Отзывы:

Нет отзывов

Похожие инструкции для , LZ6130TXPKOA

Бренд: YAT Страницы: 41

Бренд: Qualcast Страницы: 20

Бренд: Neuton Страницы: 28

Commercial Front Cut Rider YHRK20

Бренд: Yazoo Страницы: 83

Бренд: Yard-Man Страницы: 8

Бренд: Bad Boy Страницы: 20

Бренд: Toro Страницы: 72

Бренд: BOXER AGRI Страницы: 15

Бренд: MTD Страницы: 16

Бренд: Yard-Man Страницы: 36

Бренд: Brill Страницы: 96

ZT13536, ZT17542B, ZT20050

Бренд: Swisher Страницы: 28

AutoDrive 60-1827-4

Бренд: Yard Works Страницы: 53

Бренд: Kubota Страницы: 124

Бренд: Worx Страницы: 44

Southern States SO15538LT

Бренд: Southern States Страницы: 64

Бренд: Craftsman Страницы: 40

Бренд: Craftsman Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды