Husqvarna , LZ6130TXPKOA Скачать руководство пользователя | Manualshive

Страница: 33 / 84

background image

English-

31

OPERATION

In order, for example, to turn right while
moving forward, move the right control
towards the neutral position. The rotation
of the right wheel is reduced and the
machine turns to the right.

Turning on the spot can be achieved by
moving one control backward (behind
the neutral position) and carefully moving
the other steering control forward from its
neutral position.

Operating on hills

Read "Driving on Slopes" in the "Safety
Instructions"

.

•

The slowest speed possible should be
used before starting up or down hills.

•

Avoid stopping or changing speed on
hills.

•

If stopping is absolutely necessary, pull
drive levers into the neutral position and
push to the outside of the unit and
engage the park brake.

•

To restart movement, release the park
brake.

•

Pull the control levers back to the center
of the mower and press forward to regain
forward motion.

•

Make all turns slowly.

WARNING!

Do not drive up or down
hills with slopes greater
than 10 degrees. And do not
drive across any slopes.

8011-640

Stopping conditions

IMPORTANT INFORMATION
Control levers return to neutral when
released. This may cause the mower to
suddenly stop.

8011-511-1

Released parking brake

«
...
31
32
33
34
35
...
»

Содержание , LZ6130TXPKOA





















































































Отзывы:

Нет отзывов

Похожие инструкции для , LZ6130TXPKOA

Бренд: Weed Eater Страницы: 48

Бренд: Ferris Страницы: 44

Бренд: Kees Страницы: 23

Бренд: Ariens Страницы: 29

Бренд: Ferris Страницы: 60

Бренд: Garland Страницы: 120

Бренд: Grizzly Страницы: 96

Бренд: Kubota Страницы: 59

Бренд: Cub Cadet Страницы: 2

Rear Blades RB 15

Бренд: Land Pride Страницы: 1

Бренд: Land Pride Страницы: 22

Бренд: Land Pride Страницы: 64

Бренд: Land Pride Страницы: 72

Бренд: Scag Power Equipment Страницы: 23

TURF TIGER STT61V-29KB-DF

Бренд: Scag Power Equipment Страницы: 72

Бренд: Scag Power Equipment Страницы: 47

Бренд: Scag Power Equipment Страницы: 90

Бренд: Mountfield Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды