Husqvarna , LZ6130TXPKOA Скачать руководство пользователя | Manualshive

Страница: 16 / 84

background image

English-

14

SAFETY INSTRUCTIONS

run over or into anything. If necessary,
make repairs before starting.

•

Never make adjustments with the engine
running.

•

The machine is tested and approved only
with the equipment originally provided or
recommended by the manufacturer. Only
use approved repair parts for the
machine.

•

The blades are sharp and can cause
cuts and gashes. Wrap the blades or use
protective gloves when handling them.

•

Check the parking brake’s functionality
regularly. Adjust and service as
necessary.

•

The mulch blades should only be used in
familiar areas when higher quality
mowing is desired.

•

Reduce the risk of fire by removing
grass, leaves, and other debris that may
have accumulated on the machine. Allow
the machine to cool before putting it in
storage.

•

Regularly clean deck and underside of
deck, avoid spraying engine and
electrical components with water.

Transport

•

The machine is heavy and can cause
serious crushing injuries. Be extra
cautious when it is loaded on or
unloaded from a vehicle or trailer.

•

Use an approved trailer to transport the
machine. Activate the parking brake, turn
off the fuel supply, and fasten the
machine with approved fastening
devices, such as bands, chains, or
straps, when transporting.

•

Do not operate this machine on public
roadways.

•

Check and abide by local traffic
regulations before transporting the
machine on any road.

•

Do not tow this machine, it may cause
damage to the drive system.

•

Do not tow any trailers, etc. with this
mower. They may jackknife or overturn
causing damage to the mower and
possibly serious injury to the operator.

8011-644

Clean the machine regularly

IMPORTANT INFORMATION
The parking brake is not sufficient to lock
the machine in place during transport.
Ensure that the machine is well fastened
to the transport vehicle. Always reverse
the machine onto the transport vehicle to
avoid tipping it over.

WARNING!
Escaping hydraulic oil under
pressure can have sufficient
force to penetrate the skin,
causing serious injury. If injured
by escaping fluid, see a doctor
at once. Serious infection or
reaction can develop if proper
medical treatment is not
administered immdediately.

«
...
14
15
16
17
18
...
»

Содержание , LZ6130TXPKOA





















































































Отзывы:

Нет отзывов

Похожие инструкции для , LZ6130TXPKOA

Бренд: LawnMaster Страницы: 40

Бренд: Etesia Страницы: 24

Бренд: Redexim Страницы: 12

Бренд: Yard force Страницы: 30

Бренд: Gardenline Страницы: 24

Бренд: Lastec Страницы: 23

Бренд: Meec tools Страницы: 24

Бренд: Snapper Страницы: 44

Бренд: McCulloch Страницы: 60

Бренд: Lastec Страницы: 53

Yard Cruiser HZS15423KVE

Бренд: Snapper Страницы: 128

Бренд: Powersmart Страницы: 20

Бренд: elem Страницы: 85

Бренд: Wolf Garten Страницы: 31

Бренд: Toro Страницы: 56

Z580-D Z Master 74266

Бренд: Toro Страницы: 68

MULTICLIP 11-8186-99

Бренд: Stiga Страницы: 2

Standing Zero Turn Rotary Mower SZT 2648

Бренд: Jacobsen Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды