Husqvarna , LZ6130TXPKOA Скачать руководство пользователя

Страница: 35 / 84

English-

OPERATION

Stopping the Engine

Allow the engine to idle a minute in order to
attain normal operating temperature before
stopping it, if it has been worked hard. Avoid
idling the engine for longer periods, as there
is a risk of the spark plugs fouling.

Disengage the mower deck by
depressing the blade switch.

Raise the mower deck by pulling the
lifting lever backward to the transport
position.

When the machine is standing still,
activate the parking brake by pulling the
lever backward.

Move the throttle to the minimum position
(tortoise symbol). Turn the ignition key to
the stop position. Never use choke to
stop engine.

Move the steering controls outward.

Remove key. Always remove key when
leaving the mower to prevent
unauthorized use.

8011-510

Disengage the mower deck

8011-552

Raise the mower deck with the lifting lever

IMPORTANT INFORMATION
Leaving the ignition switch in any other
position than "OFF" will cause the battery
to be discharged.

Содержание , LZ6130TXPKOA





















































































Результаты поиска

Содержание , LZ6130TXPKOA

Отзывы:

Похожие инструкции для , LZ6130TXPKOA

Бренды по названию

Популярные бренды

Husqvarna , LZ6130TXPKOA, Руководство оператора

Результаты поиска

Содержание , LZ6130TXPKOA

Отзывы:

Похожие инструкции для , LZ6130TXPKOA

Бренды по названию

Популярные бренды