Husqvarna , LZ6130TXPKOA Скачать руководство пользователя

Страница: 75 / 84

English-

SERVICE JOURNAL

Service Journal

Action

Delivery Service

1. Charge the battery.

2. Mount the rear wheels.

3. Adjust the tire pressure of all wheels to 15 PSI (1 bar).

4. Mount the steering controls in the normal position.

5. Connect the seat fold-up stop.

6. Connect the cable to the safety switch under the seat.

7. Mount the arm rests on the seat’s back support.

8. Check that the right amount of oil is in the engine.

9. Check that the right amount of oil is in the hydraulic tank.

10. Adjust the position of the steering controls.

11. Fill with fuel and open the fuel valve.

12. Check that the machine has no transport damage.

13. Start the engine.

14. Check that there is drive to both wheels.

15. Vent the hydraulic system if necessary.

16. Check the mower deck adjustment.

17. Check:

The safety switch for the parking brake.

The safety switch for the mower deck.

The safety switch in the seat.

The safety switch in the steering controls.

Parking brake functionality.

Driving forward.

Driving backward.

Engaging the blades.

18. Check the idle speed.

19. Check the engine high idle speed.

Date, mtr reading, stamp, sign

Содержание , LZ6130TXPKOA





















































































Результаты поиска

Содержание , LZ6130TXPKOA

Отзывы:

Похожие инструкции для , LZ6130TXPKOA

Бренды по названию

Популярные бренды

Husqvarna , LZ6130TXPKOA, Руководство оператора

Результаты поиска

Содержание , LZ6130TXPKOA

Отзывы:

Похожие инструкции для , LZ6130TXPKOA

Бренды по названию

Популярные бренды