Husqvarna , LZ6130TXPKOA Скачать руководство пользователя

Страница: 49 / 84

English-

MAINTENANCE

Blade replacement

•

Remove blade bolt by turning
counterclockwise.

•

Install new or re-sharpened blade with
stamped "GRASS SIDE" facing towards
ground/grass (down) or “THIS SIDE UP”
facing deck and cutter housing.

•

Install and tighten blade bolt securely.

Torque blade bolt to 90 ft/lbs (122 Nm).

WARNING!

Blades are sharp. Protect your

hands with gloves and/or wrap
blades with a heavy cloth when

handling.

IMPORTANT INFORMATION
To ensure proper assembly, center hole in
blade must align with star on cutter
housing.

IMPORTANT INFORMATION
Special blade bolt is heat treated.
Replace with a Husqvarna bolt if required.
Do not use lower grade hardware than
specified.

1. Blade
2. Center hole
3. Cutter housing
4. Blade bolt
5. Lockwasher

Blade attachment

Содержание , LZ6130TXPKOA





















































































Результаты поиска

Содержание , LZ6130TXPKOA

Отзывы:

Похожие инструкции для , LZ6130TXPKOA

Бренды по названию

Популярные бренды

Husqvarna , LZ6130TXPKOA, Руководство оператора

Результаты поиска

Содержание , LZ6130TXPKOA

Отзывы:

Похожие инструкции для , LZ6130TXPKOA

Бренды по названию

Популярные бренды