Huntleigh Baby DOPPLEX 4000 Скачать руководство пользователя страница 51

Страница: 51 / 76

3. Lift print head assembly and chassis from inside paper tray. Pull paper tray

forward clear of assembly.

10.26

Paper Tray Refitting

1. Lift print head assembly and chassis. Insert paper tray ensuring that the

paper tray is located within the base tray guide.

2. Carefully refit chassis screws and tighten to 60cNm, seal with M-Coat-D.

Refit Power Supply Unit as detailed in 7.16. Align microswitch as detailed

in 7.24

3. Refit print head support plate as per 7.11 step 5 and align print head as

detailed in 7.12.

10.27

Paper Width Microswitch Removal

1. Remove main PCB as detailed in section 7.8

Remove 2 securing nuts, washer and lift switch clear of assembly.

10.28

Paper Width Microswitch Refitting

1. Refitting is the reversal of removal, ensuring paper tray is fully open during

refitting procedure.

10.29

Front Panel Connector Assembly Removal

1. Remove event marker, toco and US/FECG connectors from the main board

and remove cable ties.

2. Lift front panel connector assembly clear.

Issue: 2 Draft

Rev: a

614365

Pin No

Toco

Ultrasound

Orange

Red

White

Violet

Yellow

Black

Violet

Yellow

Brown

Orange

Black

Содержание Baby DOPPLEX 4000













































































Результаты поиска

Содержание Baby DOPPLEX 4000

Отзывы:

Похожие инструкции для Baby DOPPLEX 4000

Бренды по названию

Популярные бренды

Huntleigh Baby DOPPLEX 4000, Руководство по обслуживанию

Результаты поиска

Содержание Baby DOPPLEX 4000

Отзывы:

Похожие инструкции для Baby DOPPLEX 4000

Бренды по названию

Популярные бренды