Huntleigh Baby DOPPLEX 4000 Скачать руководство пользователя страница 40

Страница: 40 / 76

8.3

IUP Module

Power Supply

, provides an isolated supply to the ampifier and electronics in the patient

connected part of the IUP system for patient safety.

2.5V Reference

, is used to power the opto isolator.

Amplifier

, provides amplification of the siganl recieved from the IUP pressure

transducer and is fed to the driver for transfer over the opto isolated barrier via the opto

coupler.
The second amplifier provides an amplified signal with differential outputs for the fetal

monitor to interprete and display.

Issue: 2 DRAFT

Rev: a

614365

Amplifier

2.5v

Reference

Opto-

Coupler

Power

Supply

Tracking

Regulator

Driver

Amplifier

Pres

Sen

onne

+5v

Differential

Outputs

Isolation

Содержание Baby DOPPLEX 4000













































































Результаты поиска

Содержание Baby DOPPLEX 4000

Отзывы:

Похожие инструкции для Baby DOPPLEX 4000

Бренды по названию

Популярные бренды

Huntleigh Baby DOPPLEX 4000, Руководство по обслуживанию

Результаты поиска

Содержание Baby DOPPLEX 4000

Отзывы:

Похожие инструкции для Baby DOPPLEX 4000

Бренды по названию

Популярные бренды