Huntleigh Baby DOPPLEX 4000 Скачать руководство пользователя страница 50

Страница: 50 / 76

10.23

Paper Tray Open Microswitch Removal

1. Remove microswitch connector and power supply as detailed in 7.15.
2. Remove microswich and plate securing screws. Removing one screw at a time

will prevent the securing plate from dropping under the chassis. Lift

microswitch clear of assembly and clean chassis of sealant.

10.24

Paper Tray Open Microswitch Refitting

1. Place microswitch over securing plate and fit screws loosely.
2. With paper tray fully closed adjust microswitch position to register paper tray

closed.

3. Pull the left hand side of the paper tray gently, the unit may display “Paper

tray open” briefly as the paper tray is held under tension, this message must

disappear when released.

4. The switch must detect as soon as the left hand side catch is depressed and the

tray released.

5. Tighten microswitch securing screws to 35cNm.

10.25

Paper Tray Removal

1. Remove Power Supply PCB as per 7.15. Remove 6 chassis mounting screws

and disconnect stepper motor plug.

2. Remove print head support plate as detailed in 7.10 steps 1-2. (Cont’d)

Issue: 2 DRAFT

Rev: a

614365

Содержание Baby DOPPLEX 4000













































































Результаты поиска

Содержание Baby DOPPLEX 4000

Отзывы:

Похожие инструкции для Baby DOPPLEX 4000

Бренды по названию

Популярные бренды

Huntleigh Baby DOPPLEX 4000, Руководство по обслуживанию

Результаты поиска

Содержание Baby DOPPLEX 4000

Отзывы:

Похожие инструкции для Baby DOPPLEX 4000

Бренды по названию

Популярные бренды