Hunter Douglas Nantucket Скачать руководство пользователя страница 12

Страница: 12 / 28

INSTALLATION

STEP 2 — Mount the Battery Wand and Connect the Power

Cable, If Applicable

For an optional satellite battery pack, 18V DC power supply, 18V DC power supply with daisy-
chain connections, C-size satellite battery wand, or large DC power supply, the power source will
be connected after the shading is installed.

Battery Wand

Install the Battery Wand Clips

■

Attach the battery wand clips to the headrail.

IMPORTANT:

Position the clips close to the power cable.

Mount the Battery Wand into the Battery Wand Clips

■

Position the battery wand with its socket toward
the motor end of the shading.

■

Push the battery wand straight up into the
battery wand clips until it snaps into place.
Check to make sure the battery wand is secure.

CAUTION:

Be sure the cables do not

become pinched by the battery wand clips
during installation. Damage or overheating of
components could result.

Plug the Power Cable into the Battery Wand

NOTE:

When power is connected to the motor, a green LED inside the control side end cap will

flash to indicate the shading is ready for operation.

■

From the back of the shading headrail, connect
the power cable (from the motor side) into the
socket on the battery wand.

Place the socket

toward the motor end.

Battery

Wand

Power

Cable

Содержание Nantucket





























Результаты поиска

Содержание Nantucket

Отзывы:

Похожие инструкции для Nantucket

Бренды по названию

Популярные бренды

Hunter Douglas Nantucket, Установка Эксплуатация Уход

Результаты поиска

Содержание Nantucket

Отзывы:

Похожие инструкции для Nantucket

Бренды по названию

Популярные бренды