manualshive.com logo in svg

Hughes DIRECWAY DW7000, Руководство пользователя

Поделиться
Скачать
Hughes DIRECWAY DW7000 Скачать руководство пользователя страница 52

Chapter 4 • Troubleshooting

 

38

1035978-0001  Revision A

Using the terminal LEDs 
to troubleshoot

This section explains how to use LED appearance to 
troubleshoot. Refer to Figure 26 for power and cable connections 
when completing a troubleshooting procedure.

Fatal error indication

If the Power LED is off and one or more of the other LEDs is 
flashing, the unit may have to be replaced. If there is not a fatal 
error indication, proceed to the next troubleshooting step.

First try power cycling the terminal by disconnecting the power 
from the power strip or surge protector, waiting 10 seconds, and 
then plugging it back in. The unit may recover.

Unrecoverable key error

If the Power LED is off and all the other LEDs are flashing in 
unison, there is an unrecoverable key error. First try power 
cycling the terminal by disconnecting the power from the power 
strip or surge protector, waiting 10 seconds, and then plugging it 
back in. Call customer support if the unit does not recover.

Figure 26:  Remote terminal power and cable connections

Note:

If the fatal error indication continues, the unit must 

be replaced. Please contact customer support.

Содержание DIRECWAY DW7000



































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды