manualshive.com logo in svg

Hughes DIRECWAY DW7000, Руководство пользователя

Поделиться
Скачать
Hughes DIRECWAY DW7000 Скачать руководство пользователя страница 17

Chapter 1 • Introduction

 

1035978-0001  Revision A

3

How the remote terminal 
works

Figure 1 shows how the remote terminal fits into the DIRECWAY 
system architecture. The remote terminal is independent of the 
operating systems of the computers connected to it, meaning a 
computer using a Windows or MacIntosh operating system can 
browse the Internet when connected to the terminal. The terminal 
is a self-hosted unit, meaning the software required to operate the 
terminal resides in the terminal; there is no need to install 
software on the computer(s) connected to the terminal.

The terminal, in combination with an antenna, can also provide 
satellite connectivity for multiple computers on a wireless or 
wired (Ethernet) LAN. After the terminal and network are 
installed, every computer on the network can surf the Internet. To 
learn more about using the terminal with a network, see 
Appendix C – Home networking.

Figure 1:  Remote terminal’s role in the DIRECWAY system architecture

Note:

You can connect multiple home computers and laptops to 

a single DIRECWAY Internet connection at no additional cost. To 
do this, you need to have home networking equipment, which is 
not included with this product. For network setup, support and 
configuration, contact your network hardware manufacturer and/or 
operating system software developer (Hughes Network Systems, 
LLC (HNS) is not responsible for home network management and 
troubleshooting). Simultaneous use of high bandwidth 
applications by multiple users may result in degradation of speed. 
Actual speeds may vary. Speed and uninterrupted use of service 
are not guaranteed.

Содержание DIRECWAY DW7000



































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды