Hughes Network HN9260 Скачать руководство пользователя | Manualshive

Страница: 21 / 122

background image

Chapter 3 • Installing the satellite modem

1039434-0001 Revision A

21

Chapter 3

Installing the satellite modem

Installation of the HN9260 satellite modem consists of physical installation, followed
by commissioning and registration. These processes prepare the modem for
operation on the satellite network. Installation tasks include:

•

Physical installation and power-up

•

Entering parameters required for commissioning

•

Commissioning, including antenna pointing

The installation software is factory pre-installed in the satellite modem. If necessary,
this software is automatically updated as part of the installation process. You access
the installation software through a browser on your installer computer to perform
tasks such as entering required parameters.

Prerequisites for installing the modem

The following are required before you can install, commission, and register the
satellite modem:

•

The antenna and radio assembly must be installed, as instructed in the antenna
installation guide. (However, you

point

the antenna as part of the modem

commissioning process, which is explained later in this installation guide.)

•

The IFL cables must be installed and connected to the satellite modem and to the
radio assembly (LNB and transmitter).

See also

Items required for installation

on page 14 and

Related components

on

page 18.

Selecting the modem installation location

Select a location for the satellite modem that will accommodate all required cable
connections, including connection to the power source.

«
...
19
20
21
22
23
...
»

Содержание HN9260



























































































































Отзывы:

Нет отзывов

Похожие инструкции для HN9260

Бренд: SBC Страницы: 32

Бренд: Vega Absolute Страницы: 33

MT5656ZDX Series

Бренд: Multitech Страницы: 30

Touchstone CM900

Бренд: Arris Страницы: 46

Бренд: Microsoft Страницы: 37

Бренд: TeleWell Страницы: 131

SpeedStream 4200

Бренд: Siemens Страницы: 8

EDGE Speed ES75

Бренд: Siemens Страницы: 4

SpeedStream 4100

Бренд: Siemens Страницы: 9

Бренд: Siemens Страницы: 2

Бренд: Siemens Страницы: 16

Бренд: Siemens Страницы: 20

Gigaset SX685 WiMAX

Бренд: Siemens Страницы: 32

Бренд: Siemens Страницы: 56

Бренд: Siemens Страницы: 51

SIMATIC NET MODEM MD720

Бренд: Siemens Страницы: 67

Gigaset USB Stick 54

Бренд: Siemens Страницы: 70

Бренд: Siemens Страницы: 76

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды