Hughes Network HN9260 Скачать руководство пользователя страница 24

Страница: 24 / 122

Chapter 3 • Installing the satellite modem

1039434-0001 Revision A

1. Use an Ethernet cable to connect your laptop computer directly to the modem’s

LAN port, as shown in

Figure 6

Do not

connect the installer laptop to the modem through an Ethernet router or

switch.

Figure 6: Connecting the installer laptop computer to the modem

2. Make sure that neither the satellite modem nor the customer’s computer are

connected to an Ethernet router or switch.

3. If you are running firewall software on the laptop computer, disable it until you

complete installation of the modem.

The LAN LED on the front of the modem should now be on.

Connecting the power supply

Follow the instructions in

Connecting an AC/DC power supply

on page 24 or

Connecting and assembling a DC/DC power supply

on page 26.

Connecting an AC/DC power supply

The following apply to the AC/DC power supplies:

•

The input must be 120-240 VAC.

•

A suitable surge protector is recommended to protect the modem from
possible damage due to power surges.

The customer provides the surge protector. If a surge protector or power strip is not
present, use a wall outlet or other power source.

NOTICE

Содержание HN9260



























































































































Результаты поиска

Содержание HN9260

Отзывы:

Похожие инструкции для HN9260

Бренды по названию

Популярные бренды

Hughes Network HN9260, Руководство по установке

Результаты поиска

Содержание HN9260

Отзывы:

Похожие инструкции для HN9260

Бренды по названию

Популярные бренды