manualshive.com logo in svg

Hudson 63 1936, Руководство по механическим процедурам

Механическое процедурное руководство Hudson 63 1936 доступно для скачивания бесплатно на {веб-сайте}. Этот подробный мануал поможет вам освоить все особенности использования продукта. Скачайте его сейчас и воспользуйтесь всеми преимуществами Hudson 63 1936.

Поделиться
Скачать
background image

MECHANICAL PROCEDURE MANUAL

SECTION 6

Page 11

GAR-4701-6 GENERATOR SPECIFICATIONS
ROTATION           C,W.D.E.
VOLTS     6.
CONTROL     3rd Brush and Regulator.
FUSE     5 Ampere in Regulator.
BRUSH SPRING     Minimum 18 to Maximum 22
TENSION         ounces.
BEARINGS      C. E. Plain-Clearance
  .001" to .0025"
 D.E. Ball.
LUBRICATION     See text.
  Amps.
FIELD CURRENT     Volts     Max.     Min.
DRAW       6.0     3.89     3.51
   7.2     4.73     4.27
   7.6     5.04     4.56
MOTORIZING     Volts     Max.     Min.
DRAW        6.0     5.88     5.32
   7.2     6.62     5.98
   7.6     6.83     6.17
MAXIMUM     Volts     Max.     Min.
OUTPUT       6.0     17.3     15.3
   7.0     19.8     17.8
   8.0     22.5     20.5

GAR-4702    GENERATOR    SPECIFICATIONS
ROTATION     C.W.D.E.
VOLTS     6.
CONTROL     3rd Brush and Regulator. *
FUSE     None or 5 ampere in regulator.
BRUSH SPRING     Minimum 18 to Maximum 22
TENSION         ounces.
BEARINGS      C.E. Plain-Clearance
  .001" to .0025"
 D.E. Ball.
LUBRICATION     See text.
   Amps.
FIELD CURRENT     Volts     Max.     Min.
DRAW      6.0     4.10     3.70
   7.2     4.94     4.46
   7.6     5.25     4.75
MOTORIZING     Volts     Max.     Min.
DRAW      6.0     5.04     4.56
   7.2     5.78     5.22
   7.6     6.04     5.46
MAXIMUM     Volts     Max.     Min.
OUTPUT      6.0     12.8     10.8
     7.4     17.0  13.7
    8.0     17.0  15.0
*This generator can be used either with or without a regulator.
When a regulator is used it should be mounted on the dash and 
grounded.

GBK-4601-2 GENERATOR SPECIFICATIONS   
ROTATION         C.W.D.E.
VOLTS           

6

CONTROL         3rd Brush and Regulator.*
FUSE            None or 5 ampere in regulator.
BRUSH SPRING     Minimum 18 to Maximum 22
TENSION            ounces.
BEARINGS           C.E Plain-Clearance
      .001" to .0025"
     D.E. Ball.
   
LUBRICATION       See text.
      Amps.
FIELD CURRENT     Volts     Max.     Min.
DRAW             6.0     4.52         4.08
     7.2     5.46     4.94
     7.6     5.78     5.22
MOTORIZING     Volts     Max.     Min.
DRAW           6.0     4.62     4.18
     7.2     5.25     4.75
     7.6     5.57     5.03
MAXIMUM     Volts     Max.     Min.
OUTPUT.          6.0     12.3     10.3
     7.4     15.6     13.6
     8.0     17.5     15.5
   

GBK-4602    GENERATOR    SPECIFICATIONS   
ROTATION         C.W.D.E.
VOLTS         

6

CONTROL         3rd    Brush.
FUSE           5 Ampere.
BRUSH SPRING    Minimum 18 to Maximum 22
TENSION              ounces.
BEARINGS         C E Plain-Clearance
      .001" to .0025"
     D.E. Ball.
LUBRICATION      See text.
        Amps.
FIELD CURRENT     Volts     Max.     Min.
DRAW           6.0     4.36     3.94
     7.2     5.20     4.70
     7.6     5.46     4.94
MOTORIZING     Volts     Max.     Min.
DRAW           6.0     5.04     4.56
     7.2     5.78     5.22
     7.6     6.09     5.51
MAXIMUM 
OUTPUT         Volts     Max.     Min.
       6.0   15.2     13.2
     7.4     18.9     16.9
     8.0     21.0     19.0

Содержание 63 1936














































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 63 1936

ZAPTEC Go Instruction Manual preview
Go
Бренд: ZAPTEC Страницы: 240
A-Tach Mounts ST-1 Instructions preview
ST-1
Бренд: A-Tach Mounts Страницы: 2
A-Tach Mounts 50291 Quick Start Manual preview
50291
Бренд: A-Tach Mounts Страницы: 2
A-Tach Mounts 50206 Instructions preview
50206
Бренд: A-Tach Mounts Страницы: 2
FANATEC Porsche 911 Turbo S Wheel Developer Quick Manual preview
Porsche 911 Turbo S Wheel
Бренд: FANATEC Страницы: 9
Mercedes-Benz 2013 C-Class Coupe Owner'S Manual preview
2013 C-Class Coupe
Бренд: Mercedes-Benz Страницы: 388
Standby L54 Manual preview
L54
Бренд: Standby Страницы: 10
Buick 2005 Terraza Owner'S Manual preview
2005 Terraza
Бренд: Buick Страницы: 428
BMW 01 29 9 416 497 Installation Instructions preview
01 29 9 416 497
Бренд: BMW Страницы: 5
Edelbrock Chevrolet 5783 Installation Instructions preview
Chevrolet 5783
Бренд: Edelbrock Страницы: 1
FORM FIT 1308 Installation Instructions preview
1308
Бренд: FORM FIT Страницы: 2
Dometic Heki 2 Installation And Operating Manual preview
Heki 2
Бренд: Dometic Страницы: 158
Gator GX5HDKT User Manual preview
GX5HDKT
Бренд: Gator Страницы: 8
Whispbar K607W Fitting Instructions Manual preview
K607W
Бренд: Whispbar Страницы: 14
cam 40103 AL Mounting Instructions preview
40103 AL
Бренд: cam Страницы: 6
Magneti Marelli AC911 Installation Instruction preview
AC911
Бренд: Magneti Marelli Страницы: 3
Mid America Motorworks 602-781 Instruction Sheet preview
602-781
Бренд: Mid America Motorworks Страницы: 2
iDataLink BLADE-AL-HK4-EN Install Manual preview
BLADE-AL-HK4-EN
Бренд: iDataLink Страницы: 35

Бренды по названию

Популярные бренды

Загрузить еще бренды