Hudson 63 1936 Скачать руководство пользователя страница 257

Страница: 257 / 333

MECHANICAL PROCEDURE MANUAL

SECTION 21

Page 9

A similar arrangement is used on some 1934, 1935 and 1936
Brougham passenger seats except the mechanism is unlocked by

pushing forward on the seat back.

The mechanism shown in Figures 2112 and 2113 is used

on 1937 model Brougham front seats which are of the bench

type, with a divided back. The lever A controls the forward

and rearward adjustment as in the sedan type. The lever (B)

is connected to the right hand seat back so that the latch on

the right side is operated when the seat back is pushed

forward. Further forward movement of the seat back swings

the right side of the seat forward to give easy access to the

rear of the car.

These mechanisms are simple in design but may become

inoperative if an excessive amount of dirt gets into the

tracks. They should be kept clean and well lubricated at all

times.

Figure 2113-1937 Brougham Seat Mechanism—entrance

position

Содержание 63 1936














































































































































































































































































































































Результаты поиска

Содержание 63 1936

Отзывы:

Похожие инструкции для 63 1936

Бренды по названию

Популярные бренды

Hudson 63 1936, Руководство по механическим процедурам

Результаты поиска

Содержание 63 1936

Отзывы:

Похожие инструкции для 63 1936

Бренды по названию

Популярные бренды