HUBER+SUHNER MASTERLINE Extreme Hybrid Скачать руководство пользователя страница 9

Страница: 9 / 15

INSTALLATION MANUAL

Page 9 of 15

HUBER+SUHNER disclaims any liability resulting from incorrect installation and use, including any damages resulting from the use of tools and

accessories other than the ones recommended herein. Any installation performed by unqualified personnel voids the product warranty provided by

HUBER+SUHNER. All due care and attention must be exercised when performing the installation of these products. For advice concerning the

general handling of these products please contact HUBER+SUHNER.

Step 6

Feed gland nut over cable to secure to cable entry gland if
required.

Step 7

Unwind black tape at cable butt to reveal rip cord.
This cord is used to open the cable jacket and gain access to
the cable elements within.

Step 8

Use a screwdriver (or similar) to cut the cable jacket back to the
“strip-back point” marked using the tape.

Step 9

Remove cable jacket carefully.

Step 10

Unwrap copper tape from cable using gloves due to potential
sharp edges up to the “strip-back point”.

Step 11

Make sure not to leave any sharp edges where the copper foil
goes under the jacket: carefully remove excess foil with pin-
nosed pliers and then cover it with tape.

Содержание MASTERLINE Extreme Hybrid
















Результаты поиска

Содержание MASTERLINE Extreme Hybrid

Отзывы:

Похожие инструкции для MASTERLINE Extreme Hybrid

Бренды по названию

Популярные бренды

HUBER+SUHNER MASTERLINE Extreme Hybrid, Руководство по установке

Результаты поиска

Содержание MASTERLINE Extreme Hybrid

Отзывы:

Похожие инструкции для MASTERLINE Extreme Hybrid

Бренды по названию

Популярные бренды