HUBER+SUHNER MASTERLINE Extreme Hybrid Скачать руководство пользователя страница 10

Страница: 10 / 15

INSTALLATION MANUAL

Page 10 of 15

HUBER+SUHNER disclaims any liability resulting from incorrect installation and use, including any damages resulting from the use of tools and

accessories other than the ones recommended herein. Any installation performed by unqualified personnel voids the product warranty provided by

HUBER+SUHNER. All due care and attention must be exercised when performing the installation of these products. For advice concerning the

general handling of these products please contact HUBER+SUHNER.

Step 12

Carefully unwind the fibre optic cable element from the DC tails
and from a loop to separate it.

Step 13

During this process (at any stage) ensure the fibre optics are not
kinked where they exit the cable butt.
Use tape to protect the FO cable against over bending

Do not over bend the cable. Minimum bend
radius for the fiber optic cable is 8 cm

Step 14

Once fiber optic cable is separated from DC wires, attach it
temporarily to base station to keep it secure and clean.

Step 15

Tighten cable gland to secure cable and ensure IP protection.

Step 16

Measure the required DC tail length and cut them.

Step 17

Do not cut at any stage the fiber optic cable

Step 18

Route DC cable element to their respective termination points
and connect.

Route earth wire to earth bonding point and connect

Содержание MASTERLINE Extreme Hybrid
















Результаты поиска

Содержание MASTERLINE Extreme Hybrid

Отзывы:

Похожие инструкции для MASTERLINE Extreme Hybrid

Бренды по названию

Популярные бренды

HUBER+SUHNER MASTERLINE Extreme Hybrid, Руководство по установке

Результаты поиска

Содержание MASTERLINE Extreme Hybrid

Отзывы:

Похожие инструкции для MASTERLINE Extreme Hybrid

Бренды по названию

Популярные бренды