background image

INSTALLATION MANUAL 

 

 

Page 7 of 15 

HUBER+SUHNER disclaims any liability resulting from incorrect installation and use, including any damages resulting from the use of tools and 

accessories other than the ones recommended herein. Any installation performed by unqualified personnel  voids the product warranty provided by 

HUBER+SUHNER. All due care and attention must be exercised when performing the installation of these products. For advice concerning the 

general handling of these products please contact HUBER+SUHNER. 

 

Step 13 

Optional for MLEHs with connectorised power breakouts:  
 
Connect the power plug (male) connectors on the power 
jumpers with the power receptacle (female) connectors on the 
MLEH breakout cables, which are marked with labels numbered 
1 to 6 (9).  

 
Switch off the power supply before you mate or 
un-mate the power connector. Otherwise the 
contacts will get damaged. Connector is not for hot 
plugging. 

 

Mating: 
Remove protection caps of the plug. Twist (120°) the coupling 
ring of the plug connector to remove protecting cap as shown. 
Note the lock / unlock symbol on the coupling ring. 
 
Remove protection caps of the power receptacle (female) 
connectors on the MLEH breakout cables. Twist (120°) the 
coupling ring of the socket connector anticlockwise to remove 
protecting cap as shown. 
Connect the two protection caps together for later reuse. 
 

Push  plug  connector  slightly  and  in-line  into  receptacle 
connector,  rotate  to  find  keying  position,  twist  coupling  ring  of 
the plug connector clockwise as shown until you hear and feel a 
“click”. 

 

Align white strip on the plug with the white strip 
on the receptacle to find keying position easier. 

 
Make sure the plug connector is in-line with the 
receptacle connector before coupling ring is 
twisted. Otherwise the connector might be 
damaged. 

 
Avoid any tilt during mating process since the 
connector might be damaged 

 

 
Un-mating: 
Twist coupling ring on the 

plug

 (not on the receptacle) 

anticlockwise to un-mate the plug connector. Note the lock / 
unlock symbol. Mount the protection cap to avoid ingress of 
water or dirt. 

 

 

 

 

 

 

 

Step 14 

Ensure smooth routing of all cables from fiber optic and power 
jumper to the RRH equipment using HUBER+SUHNER cable 
clamps, which are available for different profiles.  

 

Do not over bend the cables. Minimum bend 
radius for power cable and fiber optic cable is 10 
cm. Avoid side load on the power and fiber optic 
connector.  
Do not use cable ties to fix cables

 

 

Step 15 

Connect fiber optic jumper with RRH interface connector and the 
power conductors with RRH power socket connector or screw 
terminals. 

 

 
 

Содержание MASTERLINE Extreme Hybrid
















Отзывы: