HUBER+SUHNER MASTERLINE Extreme Hybrid Скачать руководство пользователя страница 8

Страница: 8 / 15

INSTALLATION MANUAL

Page 8 of 15

HUBER+SUHNER disclaims any liability resulting from incorrect installation and use, including any damages resulting from the use of tools and

accessories other than the ones recommended herein. Any installation performed by unqualified personnel voids the product warranty provided by

HUBER+SUHNER. All due care and attention must be exercised when performing the installation of these products. For advice concerning the

general handling of these products please contact HUBER+SUHNER.

BASE STATION END OF ASSEMBLY

Step 1

After unwinding the whole assembly from the reel, while
handling the assembly make sure to leave the pulling tube as
long as possible on the assembly.
Pulling tube ensures IP65 and gives protection to the FO and
DC tails inside.

Step 2

To remove protective tube hold tube and loosen gland nut.

Do NOT twist the tube at any stage of removal.

Pull tube off to reveal the tails within.

Step 3

Remove gland nut from cable and keep it safe.

Step 4

Feed tails through cabinet/cabin.

Step 5

Mark the “strip-back point” using tape.

Содержание MASTERLINE Extreme Hybrid
















Результаты поиска

Содержание MASTERLINE Extreme Hybrid

Отзывы:

Похожие инструкции для MASTERLINE Extreme Hybrid

Бренды по названию

Популярные бренды

HUBER+SUHNER MASTERLINE Extreme Hybrid, Руководство по установке

Результаты поиска

Содержание MASTERLINE Extreme Hybrid

Отзывы:

Похожие инструкции для MASTERLINE Extreme Hybrid

Бренды по названию

Популярные бренды