Huawei V100R006C00 Скачать руководство пользователя страница 80

Страница: 80 / 142

The observing port is configured properly.

The mirrored port and the mirroring direction are configured properly.

7.3 Configuring Remote Port Mirroring

This section describes how to configure remote port mirroring.

7.3.1 Establishing the Configuration Task

Applicable Environment

When incoming or outgoing packets passing through one or more ports of the S5700 need to be
monitored, you can configure remote port mirroring if the monitored ports are not located on
the same S5700 as the observing port.

Pre-configuration Tasks

None.

Data Preparation

To configure remote port mirroring, you need the following data.

No.

Data

Type and number of the observing port

Number of the mirrored port

ID of the RSPAN VLAN

7.3.2 Configuring Remote Port Mirroring

Context

A mirrored port can be a physical interface or an Eth-Trunk interface.

To configure an Eth-Trunk as a mirrored port, you must run the

interface eth-trunk

trunk-id

command to create the Eth-Trunk first.

If an Eth-Trunk is configured as a mirrored port, its member interfaces cannot be configured
as mirrored ports.

If a member interface of an Eth-Trunk is configured as a mirrored port, the Eth-Trunk
cannot be configured as a mirrored port.

Procedure

Specify a mirrored port and an RSPAN VLAN on the source switch.

NOTE

The mirrored port cannot be added to the RSPAN VLAN.

Quidway S5700 Series Ethernet Switches
Configuration Guide - Device Management

7 Mirroring

Issue 01 (2011-07-15)

Huawei Proprietary and Confidential

Содержание V100R006C00















































































































































Результаты поиска

Содержание V100R006C00

Отзывы:

Бренды по названию

Популярные бренды

Huawei V100R006C00, Руководство по настройке

Результаты поиска

Содержание V100R006C00

Отзывы:

Бренды по названию

Популярные бренды