Huawei V100R006C00 Скачать руководство пользователя страница 119

Страница: 119 / 142

Delete the observing port.
# Delete the observing port GigabitEthernet 0/0/24.

system-view

[Switch]

undo observe-port 1

Change the observing port.
# Change the observing port to GigabitEthernet 0/0/5.

[Switch]

observe-port 1 interface GigabitEthernet 0/0/5

Configure a mirrored port.
# Configure GigabitEthernet 0/0/1 as the mirrored port again.

[Switch]

interface GigabitEthernet 0/0/1

[Switch-GigabitEthernet0/0/1]

port-mirroring to observe-port 1 inbound

[Switch-GigabitEthernet0/0/1]

quit

Verify the configuration.
# Run the

display port-mirroring

command. You can check the configurations on the

current observing port and mirrored port.

[Switch]

display port-mirroring

Port-
mirror:
----------------------------------------------------------
Mirror-port Direction Observe-port
----------------------------------------------------------
GigabitEthernet0/0/1 Inbound
GigabitEthernet0/0/5

Configuration Files

Configuration file of the Switch

#
sysname Switch
#
observe-port 1 interface GigabitEthernet0/0/5
#
interface GigabitEthernet0/0/1
port-mirroring to observe-port 1 inbound
#
return

Quidway S5700 Series Ethernet Switches
Configuration Guide - Device Management

7 Mirroring

Issue 01 (2011-07-15)

Huawei Proprietary and Confidential

110

Содержание V100R006C00















































































































































Результаты поиска

Содержание V100R006C00

Отзывы:

Бренды по названию

Популярные бренды

Huawei V100R006C00, Руководство по настройке

Результаты поиска

Содержание V100R006C00

Отзывы:

Бренды по названию

Популярные бренды