manualshive.com logo in svg

Huawei V100R006C00, Руководство по настройке

Поделиться
Скачать
Huawei V100R006C00 Скачать руководство пользователя страница 112

Figure 7-7

 Networking diagram of local flow mirroring

Router

Switch

GE0/0/3

GE 0/0/1

GE0/0/24

L2 Switch

Mirroring host

GE0/0/5

L2 Switch

 

Configuration Roadmap

The configuration roadmap is as follows:

1.

Configure GigabitEthernet 0/0/24 as an observing port.

2.

Create a traffic classifier and set the traffic classification rule that only the packets with the
802.1p priority as 6 can be matched.

3.

Create a traffic behavior and configure flow mirroring in the traffic behavior.

4.

Create a traffic policy and bind the traffic classifier to the traffic behavior.

5.

Apply the traffic policy to GigabitEthernet 0/0/1 and GigabitEthernet 0/0/5.

6.

Create a VLAN on the Switch. Add GigabitEthernet 0/0/1, GigabitEthernet 0/0/3, and
GigabitEthernet 0/0/5 to the same VLAN in trunk mode.

Data Preparation

To complete the configuration, you need the following data:

l

Name of the traffic classifier: c1

l

Name of the traffic behavior: b1

l

Name of the traffic policy: p1

l

ID of the VLAN created on the Switch: 1

Configuration Procedure

1.

Create a VLAN on the Switch and add interfaces to the VLAN in trunk mode.
# Add GigabitEthernet 0/0/1, GigabitEthernet 0/0/3, and GigabitEthernet 0/0/5 to the same
VLAN in trunk mode. The following takes the configuration of GigabitEthernet 0/0/1 as
an example. The configurations of GigabitEthernet 0/0/3 and GigabitEthernet 0/0/5 are the
same as the configuration of GigabitEthernet 0/0/1 and are not mentioned here.

Quidway S5700 Series Ethernet Switches
Configuration Guide - Device Management

7 Mirroring

Issue 01 (2011-07-15)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

103

Содержание V100R006C00















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды