manualshive.com logo in svg

Huawei V100R006C00, Руководство по настройке

Поделиться
Скачать
Huawei V100R006C00 Скачать руководство пользователя страница 21

Context

You can check different items in different phases in the Auto-Config process to confirm that
Auto-Config runs properly.

Procedure

Step 1

Five minutes after unconfigured switches are powered on, check address allocation on the DHCP
server to confirm that the switches are connected to the DHCP server.

NOTE

If the switches are connected to the DHCP server, you can log in to the switches through Telnet but do not
configure the switches.

Step 2

Five minutes after the switches obtain IP addresses, check the file downloading log on the FTP/
TFTP server or log in to the switches to confirm that correct configuration files have been
downloaded.

NOTE

Do not save a configuration file to a switch to be configured immediately after the configuration file is
downloaded; otherwise, only a temporary configuration file is saved because the configurations have not
taken effect.

Step 3

If the user has specified the activation delay, the configuration file will take effect after the delay.
If the user has not specified the activation delay, the configuration file will take effect
immediately by default. Then run the 

display current-configuration

 command to check

whether the configurations take effect.

NOTE

If you access the switch when it is busy delivering configurations in the Auto-Config process, the switch
may not respond in real time.
After the configurations take effect, modify the configuration of the downstream interface on the DHCP
relay as required.

----End

Quidway S5700 Series Ethernet Switches
Configuration Guide - Device Management

1 Auto-Config

Issue 01 (2011-07-15)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

12

Содержание V100R006C00















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды