manualshive.com logo in svg

Huawei V100R006C00, Руководство по настройке

Поделиться
Скачать
Huawei V100R006C00 Скачать руководство пользователя страница 111

#
sysname Switch
#
 vlan batch 10
#
 observing-port 1 interface GigabitEthernet0/0/3
#
vlan 10
 mac-mirroring 0001-0001-0001 to observe-port 1 inbound
#
interface GigabitEthernet0/0/1
 port link-type trunk 
 port trunk allow-pass vlan 10
#
interface GigabitEthernet0/0/2
 port link-type trunk 
 port trunk allow-pass vlan 10
#
interface GigabitEthernet0/0/3
 port link-type trunk 
 port trunk allow-pass vlan 10
#
interface GigabitEthernet0/0/4
 port link-type trunk 
 port trunk allow-pass vlan 10
#
                                     
#
return

7.17.4 Example for Configuring Local Flow Mirroring

Networking Requirements

As is shown in 

Figure 7-7

, the Switch is connected to two L2 switches through

GigabitEthernet 0/0/1 and GigabitEthernet 0/0/5. Packets with the same attributes received by
GigabitEthernet 0/0/1 and GigabitEthernet 0/0/5 and transmitted from GigabitEthernet 0/0/3
need to be monitored. In this example, packets with the 802.1p priority as 6 need to be monitored.

GigabitEthernet 0/0/24 is configured as an observing port.

Quidway S5700 Series Ethernet Switches
Configuration Guide - Device Management

7 Mirroring

Issue 01 (2011-07-15)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

102

Содержание V100R006C00















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды