manualshive.com logo in svg

Huawei V100R006C00, Руководство по настройке

Поделиться
Скачать
Huawei V100R006C00 Скачать руководство пользователя страница 107

Configuration Procedure

1.

Create a VLAN on the Switch and add interfaces to the VLAN in trunk mode.

# Add GigabitEthernet 0/0/1 and GigabitEthernet 0/0/3 to a same VLAN in trunk mode.
The following takes the configuration of GigabitEthernet 0/0/1 as an example. The
configuration of GigabitEthernet 0/0/3 is the same as the configuration of
GigabitEthernet 0/0/1 and is not mentioned here.

<Switch> 

system-view

[Switch] 

vlan 1

[Switch-vlan1] 

quit

[Switch] 

interface gigabitethernet 0/0/1

[Switch-GigabitEthernet0/0/1] 

port trunk allow-pass vlan 1

[Switch-GigabitEthernet0/0/1] 

quit

2.

Configure an observing port.

# Set GigabitEthernet 0/0/24 as the observing port.

<Switch> 

system-view

[Switch] 

observing-port 1 interface GigabitEthernet 0/0/24

3.

Configure a mirrored port.

# Set GigabitEthernet 0/0/1 as a mirrored port.

[Switch] 

interface gigabitethernet 0/0/1

[Switch-GigabitEthernet0/0/1] 

port-mirroring to observe-port 1 inbound

[Switch-GigabitEthernet0/0/1] 

quit

4.

Verify the configuration.

# Run the 

display port-mirroring

 command. You can check the configurations on the

observing port and mirrored port.

[Switch] 

display port-mirroring

 Observe index 1 is set to interface GigabitEthernet0/0/24
   Observe Type: Local
 Interface GigabitEthernet0/0/1
  Mirrored to: Observe index 1
    Direction: inbound
 Observe index 2 is not set to any interface
 Observe index 3 is not set to any interface
 Observe index 4 is not set to any interface 

Configuration Files

Configuration file of the Switch

#
vlan batch 1
#
 sysname Switch
#
 observing-port 1 interface GigabitEthernet0/0/24
#
interface GigabitEthernet0/0/1
 port trunk allow-pass vlan 1
 port-mirroring to observe-port 1 inbound
#
interface GigabitEthernet0/0/3
 port trunk allow-pass vlan 1
#
return

7.17.2 Example for Configuring Local VLAN Mirroring

Quidway S5700 Series Ethernet Switches
Configuration Guide - Device Management

7 Mirroring

Issue 01 (2011-07-15)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

98

Содержание V100R006C00















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды