manualshive.com logo in svg

Huawei V100R006C00, Руководство по настройке

Поделиться
Скачать
Huawei V100R006C00 Скачать руководство пользователя страница 30

[SwitchB-GigabitEthernet0/0/1]

 nap local-ip 12.12.12.5 sub-ip 12.12.12.9 peer-ip 

12.12.12.6 sub-ip 12.12.12.10 30

Are you sure to continue?[Y/N]

 y

# After the preceding configuration is complete, run the 

display nap status

 command on

Switch B. You can view that NAP has been enabled on Switch B. Then, run the 

display nap

interface

 command. You can view that the primary and secondary IP addresses have been

assigned to the master and slave interfaces. For example:

[SwitchB-GigabitEthernet0/0/1]

 display nap status

Slave port status         : Enable
 Nap ip-pool/Mask          : 10.167.253.0/24
[SwitchB-GigabitEthernet0/0/1]

 display nap interface

------------------------------------------------------
 NAP master port list 
 Port count           : 1
------------------------------------------------------
 Port property                           : Master
 Current status                          : IP-ASSIGNED
 Local port                              : GigabitEthernet0/0/1
 Peer port                               : GigabitEthernet0/0/1
 Local primary ip                        : 12.12.12.5
 Peer primary ip                         : 12.12.12.6
 Local secondary ip                      : 12.12.12.9
 Peer secondary ip                       : 12.12.12.10
 Hello time                              : 3s
 Linked time                             : 00:02:33
------------------------------------------------------

Step 3

Log in to the slave device from the master device.

# Configure Switch B.

[SwitchB-GigabitEthernet0/0/1]

 nap login neighbor

Trying 12.12.12.10 ...
Press CTRL+K to abort
Connected to 12.12.12.10 ...

Info: The max number of VTY users is 10, and the number
      of current VTY users on line is 1.

Step 4

Disable NAP on the slave device.

# Configure Switch C.

<Quidway>

 system-view

[Quidway]

 sysname SwitchC

[SwitchC]

 undo nap slave enable

----End

Configuration Files

None

2.3.2 Example for Configuring NAP-based Remote Deployment in
Automatic Mode

In this example, the temporary neighbor relationship is set up between a switch and another
switch that has the empty configuration to implement remote deployment in automatic mode.

Networking Requirements

As shown in 

Figure 2-2

, the user needs to perform a remote login to Switch B from Switch A.

Switch B is the master device, and temporary neighbor relationship is to be set up between

Quidway S5700 Series Ethernet Switches
Configuration Guide - Device Management

2 NAP Configuration

Issue 01 (2011-07-15)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

21

Содержание V100R006C00















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды