manualshive.com logo in svg

Huawei V100R006C00, Руководство по настройке

Поделиться
Скачать
Huawei V100R006C00 Скачать руководство пользователя страница 43

The reserved VLAN of the stack is configured on the master switch.

Procedure

Step 1

Run:

system-view

The system view is displayed.

Step 2

Run:

stack reserved-vlan

 

vlan-id

The reserved VLAN is configured.

By default, a stack system uses VLAN 4093 as the reserved VLAN.

NOTE

The reserved VLAN cannot be used for other services.

----End

3.5.3 (Optional) Enabling the Stacking Function

Context

Before connecting stack devices through leased stack cables, do as follows on the stacking-
capable devices.

Procedure

Step 1

Run:

system-view

The system view is displayed.

Step 2

Run:

stack enable

The stacking function is enabled on the S5700.

By default, the stacking function is enabled.

NOTE

If you run the 

undo stack enable

 command to disable the stacking function on the S5700, the configuration

takes effect only after the S5700 is restarted. If you run the 

stack enable

 command to enable the stacking

function on the S5700, the configuration takes effect only after the S5700 is restarted.

----End

3.5.4 (Optional) Configuring a Stack ID for the S5700

Context

Stack IDs can be configured before or after the stack system is created. By default, stack IDs of
member switches in a stack are all 0s. If stack IDs are not configured for member switches before
the stack system is created, the stack system assigns stack IDs to member switches after being

Quidway S5700 Series Ethernet Switches
Configuration Guide - Device Management

3 Stacking

Issue 01 (2011-07-15)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

34

Содержание V100R006C00















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды