Huawei V100R006C00 Скачать руководство пользователя страница 108

Страница: 108 / 142

Networking Requirements

, GigabitEthernet0/0/1 is connected to PC1; GigabitEthernet0/0/2 is

connected to PC2. PC1 and PC2 belong to VLAN 10. Now, incoming traffic of all active
interfaces in VLAN 10 needs to be monitored. In this case, you can configure local VLAN
mirroring.

GigabitEthernet0/0/3 serves as an observing port.

Figure 7-5

Networking diagram of local VLAN mapping

PC1

PC2

GE0/0/2

GE0/0/3

GE0/0/1

PC3

Configuration Roadmap

The configuration roadmap is as follows:

Configure GigabitEthernet0/0/3 as an observing port.

Configure VLAN 10 as a mirrored VLAN.

Data Preparation

None.

Configuration Procedure

Add GigabitEthernet0/0/1 and GigabitEthernet0/0/2 to VLAN 10 as access interfaces.
# Add GigabitEthernet0/0/1 to VLAN 10 as an access interface.

system-view

[Switch]

interface gigabitethernet 0/0/1

[Switch-GigabitEthernet0/0/1]

port link-type access

[Switch-GigabitEthernet0/0/1]

port default vlan 10

[Switch-GigabitEthernet0/0/1]

quit

Add GigabitEthernet0/0/2 to VLAN 10 as an access interface in the same way.

Configure an observing port.
# Set GigabitEthernet0/0/3 as an observing port.

[Switch]

observing-port 1 interface gigabitethernet 0/0/3

Configure a mirrored VLAN.

Quidway S5700 Series Ethernet Switches
Configuration Guide - Device Management

7 Mirroring

Issue 01 (2011-07-15)

Huawei Proprietary and Confidential

Содержание V100R006C00















































































































































Результаты поиска

Содержание V100R006C00

Отзывы:

Бренды по названию

Популярные бренды

Huawei V100R006C00, Руководство по настройке

Результаты поиска

Содержание V100R006C00

Отзывы:

Бренды по названию

Популярные бренды