Huawei FusionModule 1000A20 Скачать руководство пользователя

Страница: 54 / 86

FusionModule1000A20 Prefabricated All-in-One Data
Center
Maintenance Guide

4 Parts Replacement

Issue 01 (2019-07-15)

Figure 4-15

Removing a camera

Step 2

Use a Phillips screwdriver to remove the screws that fasten the camera to its base.

Step 3

Remove the network cable and take out the camera.

Step 4

Install the new camera by following instructions in documents delivered with the camera,
tighten the screws to secure the camera to the base, and reconnect the network cable in the
original way.

Step 5

Adjust the angle of the camera to cover the monitored area by following instructions in
documents delivered with the camera.

Step 6

Configure the camera by referring to the management system initial configuration table.

The original parameter settings can be used.

Step 7

Check that the new camera is working properly.

----End

4.3.6 Replacing Access Control Components

4.3.6.1 Replacing an IC Card Reader

Prerequisites

A spare IC card reader of the same model is available and functional.

Impact on the System

None

Preparations

Tools: Phillips screwdriver, protective gloves

Materials: access card, spare IC card reader

Skill requirement: ELV engineer

Содержание FusionModule 1000A20























































































Результаты поиска

Содержание FusionModule 1000A20

Отзывы:

Похожие инструкции для FusionModule 1000A20

Бренды по названию

Популярные бренды

Huawei FusionModule 1000A20, Руководство по обслуживанию

Результаты поиска

Содержание FusionModule 1000A20

Отзывы:

Похожие инструкции для FusionModule 1000A20

Бренды по названию

Популярные бренды