Huawei FusionModule 1000A20 Скачать руководство пользователя страница 43

Страница: 43 / 86

FusionModule1000A20 Prefabricated All-in-One Data
Center
Maintenance Guide

4 Parts Replacement

Issue 01 (2019-07-15)

Figure 4-6

Replacing the module



If one SPD module is damaged by lightening, it is recommended that all SPD modules be replaced.



If the SPD module cannot be pulled out, use a tool such as a flat-head screwdriver to lever it out.

Step 5

Install the spare SPD module, and switch on the SPD circuit breaker.

Step 6

Reinstall the protective panel.

----End

Follow-up Procedure

Dispose of the removed SPD module that is confirmed faulty.

4.1.2.6 Replacing an Indicator

Prerequisites



An indicator is dim or faulty.



Spare indicators of the same model are available and functional.

Impact on the System

None

Preparations

Tools: Phillips screwdriver, multimeter

Materials: spare indicator

Documents: none

Skill requirement: electrician's work permit

Procedure

Step 1

Switch off the protective miniature circuit breaker (MCB) or fuse.

Содержание FusionModule 1000A20























































































Результаты поиска

Содержание FusionModule 1000A20

Отзывы:

Huawei FusionModule 1000A20, Руководство по обслуживанию, Страница: 43 / 86

Результаты поиска

Содержание FusionModule 1000A20

Отзывы: