Huawei FusionModule 1000A20 Скачать руководство пользователя

Страница: 28 / 86

FusionModule1000A20 Prefabricated All-in-One Data
Center
Maintenance Guide

3 Routine Maintenance

Issue 01 (2019-07-15)

Extinguishan
t control
panel
batteries

Operation

Check Standard

Maintenance Guide

control panel so that
the batteries power
the panel.

Measure the battery
voltage using a
multimeter.

The battery voltage is 24±1 V
DC.

Hand-held fire
extinguisher

Check the hand-held
fire extinguisher.

The hand-held fire extinguisher is
in good condition.

Replace the hand-held fire
extinguisher.

The pressure pointer of the
hand-held fire extinguisher is in
the green zone.

The fire extinguisher is within the
validity period.

3.4.4 Other Systems

Table 3-10

Quarterly maintenance checklist for other systems

Item

Method

Check Standard

Troubleshooting

Ventilation
vent air filter

Check whether the filter
is blocked.

The air filter is not
blocked.

If an air filter is slightly blocked, clean the
air filter and reinstall it. If more than 50% of
the meshes are blocked, replace the air filter.

Pre-fab.
module body

Check the pre-fab.
module.

The pre-fab.
module is clean.

Clean the pre-fab. module using a
long-handled soft brush and alkaline or
neutral detergent.

Wash the pre-fab. module with clean
water.

Pre-fab.
module
repainting

Check the pre-fab.
module exterior for
damage or corrosion.

The pre-fab.
module and bases
are free from paint
flake-off, rust, or
corrosion.

Maintain or replace the rusty or damaged
part of the pre-fab. modules. Repaint areas
with paint flake-off or rust.

Содержание FusionModule 1000A20























































































Результаты поиска

Содержание FusionModule 1000A20

Отзывы:

Похожие инструкции для FusionModule 1000A20

Бренды по названию

Популярные бренды

Huawei FusionModule 1000A20, Руководство по обслуживанию

Результаты поиска

Содержание FusionModule 1000A20

Отзывы:

Похожие инструкции для FusionModule 1000A20

Бренды по названию

Популярные бренды