Huawei FusionModule 1000A20 Скачать руководство пользователя | Manualshive

Страница: 25 / 86

background image

FusionModule1000A20 Prefabricated All-in-One Data
Center
Maintenance Guide

3 Routine Maintenance

Issue 01 (2019-07-15)

Copyright © Huawei Technologies Co., Ltd.

18

Maintenance
Item

Instructions

Criteria

Troubleshooting

the indicators.

power indicators
are bright.

dim light.

Check the SPD
indicator and SPD
circuit breaker status.

The SPD indicator
is green.

If the SPD indicator is red, replace the SPD.

The SPD circuit
breaker is switched
to ON.

Switch on the circuit breaker.

(Optional) Push any
button on the PD510
electricity meter LCD.

The PD510
electricity meter
LCD lights up and
displays
information
properly.

1.

If the LCD does not display information
properly (no display or fuzzy), check
whether the power cable is properly
connected.

2.

If the power cable is properly connected,
replace the PD510.

3.4.2 Surveillance system

Table 3-8

Quarterly maintenance checklist for the monitoring system

Check Item

Description

Criteria

Troubleshooting

Temperature
and humidity
(T/H) sensor

Use a hand-held
thermohygrograp
h to measure
both the humidity
and temperature
in an aisle.
Compare the
measured values
with the values
displayed on the
ECC800.

The values measured are
consistent with the those
displayed on the
ECC800. The
temperature difference is
within ±2°C, and the
humidity difference
within ±5% RH.

If the differences exceed the allowed range,
replace the T/H sensor.

Access
actuator

Power input

Input voltage: 36–60 V
DC

Check the input power cables if the input
voltage is abnormal.

PWR indicator

Steady on: The power
supply is normal.

Off: No power supply is
available.

Check the input power cables.

ALM indicator

Steady on: A fault alarm
is raised.

Off: No fault alarm is
raised.

Clear the alarm by referring to the ECC800
documents.

RUN indicator

Off: The power supply is
abnormal.

Blinking slowly: The

Check the power supply.

Check the power supply. If the RUN
indicator blinks fast, check whether the

«
...
23
24
25
26
27
...
»

Содержание FusionModule 1000A20























































































Отзывы:

Нет отзывов

Похожие инструкции для FusionModule 1000A20

Video Investigation Portable

Бренд: SalvationData Страницы: 37

Бренд: WEG Страницы: 2

Бренд: Agilent Technologies Страницы: 177

Бренд: Keelin Страницы: 19

Бренд: iGen Страницы: 32

Бренд: Omega Страницы: 297

Бренд: ELEKON Страницы: 2

Бренд: ELEKON Страницы: 4

Saveris 0572 2800

Бренд: TESTO Страницы: 20

Бренд: TESTO Страницы: 42

Бренд: Thies CLIMA Страницы: 56

Бренд: Novalynx Страницы: 17

Бренд: In-situ Страницы: 4

Rugged TROLL 200

Бренд: In-situ Страницы: 3

Бренд: In-situ Страницы: 4

Бренд: In-situ Страницы: 24

Бренд: In-situ Страницы: 24

Бренд: In-situ Страницы: 62

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды