Huawei FusionModule 1000A20 Скачать руководство пользователя страница 44

Страница: 44 / 86

FusionModule1000A20 Prefabricated All-in-One Data
Center
Maintenance Guide

4 Parts Replacement

Issue 01 (2019-07-15)

Step 2

Replace the indicator if no voltage is detected by using a multimeter.

Step 3

Loosen the screw at the rear of the indicator and remove the conducting wire.

Figure 4-7

Removing an indicator

When removing cables, label the cables with corresponding terminal ports for later connection.

Step 4

Remove the retaining ring from the indicator and remove the indicator from the mounting
hole.

Step 5

Install a new indicator on the mounting hole, secure the retaining ring, reconnect the
conducting wire, and switch on the MCB.

----End

Follow-up Procedure

Dispose of the removed indicator that is confirmed faulty.

4.1.3 Replacing a Battery for the DC Power System

Prerequisites

A spare battery of the same model is available and functional.

Impact on the System

None

Preparations

Tools: pallet truck, wrench, protective gloves

Materials: insulation tape, spare battery, copper bar or cable

Documents: documents delivered with the DC power system battery, power supply and
distribution system diagram, power supply and distribution device layout

Содержание FusionModule 1000A20























































































Результаты поиска

Содержание FusionModule 1000A20

Отзывы:

Huawei FusionModule 1000A20, Руководство по обслуживанию, Страница: 44 / 86

Результаты поиска

Содержание FusionModule 1000A20

Отзывы: