Huawei FusionModule 1000A20 Скачать руководство пользователя страница 39

Страница: 39 / 86

FusionModule1000A20 Prefabricated All-in-One Data
Center
Maintenance Guide

4 Parts Replacement

Issue 01 (2019-07-15)

Impact on the System

Certain services of the FusionModule1000 are interrupted.

Preparations

Tools: Phillips screwdriver, flat-head screwdriver, key to the PDF door, step ladder

Materials: spare ATS controller

Documents: documents delivered with the PDF

Skill requirement: power distribution engineers

Procedure

Step 1

Open the front door of the PDF, turn off the output switches in the PDF, and turn off the
upstream and downstream switches.

Step 2

Remove the protective panel of the PDF.

Step 3

Remove the cables at the ATS controller top and label them.

Step 4

Remove the screws that secure the copper bars above and below the ATS controller, and
remove the copper bars.

Figure 4-3

Removing copper bars

Step 5

Remove the screws from the inner layer of the copper bar below the ATS controller.

Step 6

Remove the four screws that secure the ATS controller to the base and take out the input
switch.

Содержание FusionModule 1000A20























































































Результаты поиска

Содержание FusionModule 1000A20

Отзывы:

Huawei FusionModule 1000A20, Руководство по обслуживанию, Страница: 39 / 86

Результаты поиска

Содержание FusionModule 1000A20

Отзывы: