Huawei FusionModule 1000A20 Скачать руководство пользователя

Страница: 38 / 86

FusionModule1000A20 Prefabricated All-in-One Data
Center
Maintenance Guide

4 Parts Replacement

Issue 01 (2019-07-15)

Procedure

Step 1

Open the front door of the PDF, turn off the output switches in the PDF, and turn off the
upstream and downstream switches.

Step 2

Remove the protective panel of the PDF.

Step 3

Remove the three screws from the upper short-circuit copper bar using a socket wrench and
take out the short-circuit copper bar.

Step 4

Loosen the six screws that secure the input switch to the copper bar.

Step 5

Remove the two screws that secure the input switch to the base, and pull out the input switch.

Figure 4-2

Removing an input switch

Step 6

Install the new input switch and secure it using screws.

Step 7

Reinstall the short-circuit copper bar.

Step 8

Reinstall the protective panel of the PDF.

Step 9

Turn on the upstream, input, and output switches of the PDF.

Step 10

Check that the new input switch is working properly.

Step 11

Turn on downstream switches of the PDF.

----End

Follow-up Procedure

Dispose of the removed input switch that is confirmed faulty.

4.1.2.3 Replacing an ATS Controller (02404923)

Prerequisites

A spare ATS controller of the same model is available and functional.

Содержание FusionModule 1000A20























































































Результаты поиска

Содержание FusionModule 1000A20

Отзывы:

Похожие инструкции для FusionModule 1000A20

Бренды по названию

Популярные бренды

Huawei FusionModule 1000A20, Руководство по обслуживанию

Результаты поиска

Содержание FusionModule 1000A20

Отзывы:

Похожие инструкции для FusionModule 1000A20

Бренды по названию

Популярные бренды