Huawei FusionModule 1000A20 Скачать руководство пользователя страница 53

Страница: 53 / 86

FusionModule1000A20 Prefabricated All-in-One Data
Center
Maintenance Guide

4 Parts Replacement

Issue 01 (2019-07-15)

Impact on the System

The device at the rear of the ETH converter is disconnected.

Preparations

Tools: ESD wrist strap, ESD gloves, step ladder, label, marker

Material: ETH converter

Documents: none

Skill requirement: ELV engineer

Procedure

Step 1

Label each cable based on the corresponding ports on the ETH converter.

Step 2

Disconnect cables from the ETH converter.

Step 3

Remove the faulty ETH converter.

Step 4

Install the spare ETH converter in the original position and connect the cables.

----End

4.3.5 Replacing a Camera

Prerequisites

A spare camera of the same model is available and functional.

Impact on the System

Video surveillance stops.

Preparations

Tools: Phillips screwdriver, step ladder, protective gloves

Material: spare camera

Documents: documents delivered with the camera, management system initial configuration
table

Skill requirement: weak-current engineer

Procedure

Step 1

Remove the base, as shown in the right figure. Align the mark on the base with that on the
upper cover. Press the position marked with A to separate the base from the upper cover.

Содержание FusionModule 1000A20























































































Результаты поиска

Содержание FusionModule 1000A20

Отзывы:

Huawei FusionModule 1000A20, Руководство по обслуживанию, Страница: 53 / 86

Результаты поиска

Содержание FusionModule 1000A20

Отзывы: