Huawei FusionModule 1000A20 Скачать руководство пользователя страница 51

Страница: 51 / 86

FusionModule1000A20 Prefabricated All-in-One Data
Center
Maintenance Guide

4 Parts Replacement

Issue 01 (2019-07-15)

Figure 4-13

Installing the Micro SD and SIM card

Step 7

Install the spare ECC800 main control module in the ECC800 subrack and tighten the screws
on both sides of the ECC800 main control module.

Step 8

Connect the communications cables and antennas to the ECC800 main control module.

Step 9

Choose

Maintenance

Configuration File

and import the backup configuration file, or set

parameters for the devices that connect to the ECC800 to ensure normal communication.

----End

4.3.2 Replacing an ECC800 PSU

Prerequisites

Do not touch the terminals in the rear of a removed PSU to avoid electric shocks.



Tool: insulation gloves



Materials: a reserved undamaged and undeformed PSU of the appropriate model.

Context

The PSU is hot-swappable.

Procedure

Step 1

Push the locking latch in the upper right corner of the PSU panel leftwards.

Step 2

Pull out the handle of the PSU to remove the PSU from the subrack.

Step 3

Gently push the reserved PSU into the subrack along guide rails, and push the locking latch
rightwards to secure the handle.

Содержание FusionModule 1000A20























































































Результаты поиска

Содержание FusionModule 1000A20

Отзывы:

Huawei FusionModule 1000A20, Руководство по обслуживанию, Страница: 51 / 86

Результаты поиска

Содержание FusionModule 1000A20

Отзывы: