Huawei Airbridge cBTS3612 Скачать руководство пользователя страница 46

Страница: 46 / 101

On-site Maintenance Manual
Airbridge cBTS3612 CDMA Base Station

Chapter 3 Component Failure

Handling

3-9

order between the BTS and BSC should be the same), only so can

the BTS intercept the IMA/UNI configuration in the BSC.

The E1 trunk calbe problem or the connecting order mistakes

can be located by the E1 loopback test.

The IMA/UNI configuration can be obtained by querying the

dedicated status of the BTS boards.

II.

BSC interface board (XIE) failure

If E1 trunk cable is found in good connection and the connecting

order is correct after the E1 loopback test, there must be something

wrong with the BSC interface board (XIE). Rest or replace the XIE.

III.

BSC and OMC failure or incorrect configuration

If we find out the status of the link and the IMA link set of the

BCIM are normal by querying the dedicated status of the BTS board

while the problem still sustains, it could be the BSC or OMC failure or

data configuration errors. Refer to “2.4 OML Failure” and “2.5

Abis Signaling Link Failure” for details.

Содержание Airbridge cBTS3612






































































































Результаты поиска

Содержание Airbridge cBTS3612

Отзывы:

Похожие инструкции для Airbridge cBTS3612

Бренды по названию

Популярные бренды

Huawei Airbridge cBTS3612, Руководство по обслуживанию

Результаты поиска

Содержание Airbridge cBTS3612

Отзывы:

Похожие инструкции для Airbridge cBTS3612

Бренды по названию

Популярные бренды