Huawei Airbridge cBTS3612 Скачать руководство пользователя страница 33

Страница: 33 / 101

On-site Maintenance Manual
Airbridge cBTS3612 CDMA Base Station

Chapter 2 General Fault

Processing

2-14

Failure in communication link between BCKM and BCIM

Please refer to “Board Communication Link Failure” in the “3.2

Handling of Common Board Failure”.

II.

Abnormal IMA group and UNI status

If E1 connection is used for the physical layer of the OML, we

can configure it to IMA or UNI mode according to the actual needs. If

IMA link set status or UNI status is not correct, the OML will fail.

Through querying the dedicated status of the board on the BTS

maintenance console, we can acquire the IMA link set status or UNI

status.

If there is anything abnormal in the IMA link set status or UNI

status, we will have to check them one by one:

Whether E1 link is correct. It can be checked with a

loopback test.

If IMA mode is used, we need to first find out whether the

multiple pairs of E1s match each other between the BTS

and BSC, i.e. the No.N pair of E1s in the IMA link set at the

BSC side matches the No.N pair of E1s in the IMA link set

in the BTS (N=1~8).

Whether the configuration of the IMA link set of the BSC

and BTS are the same.

III.

Incorrect VCI configuration in the CMUX of the CDMA

BSC Basic Management Subrack (CBMS)

The precondition of successful establishment OML of the BTS is

the successful BOOTP request. BOOTP request package requires

Содержание Airbridge cBTS3612






































































































Результаты поиска

Содержание Airbridge cBTS3612

Отзывы:

Похожие инструкции для Airbridge cBTS3612

Бренды по названию

Популярные бренды

Huawei Airbridge cBTS3612, Руководство по обслуживанию

Результаты поиска

Содержание Airbridge cBTS3612

Отзывы:

Похожие инструкции для Airbridge cBTS3612

Бренды по названию

Популярные бренды