Huawei Airbridge cBTS3612 Скачать руководство пользователя страница 36

Страница: 36 / 101

On-site Maintenance Manual
Airbridge cBTS3612 CDMA Base Station

Chapter 2 General Fault

Processing

2-17

2.5

Abis Signaling Link Failure

2.5.1 Fault Description

After the BTS start-up, the Abis signaling link between the BTS

and BSC can not be established, or there are sometimes broken

links when the BTS is running.

From the BTS maintenance console, we can see the alarm

“Abis signaling link failure”.

2.5.2 Troubleshooting

Abnormal IMA group or UNI status

Please refer to “2.4 OML Failure” for details.

II.

Incorrect Abis signaling link parameter configuration

If the IMA link set status and the UNI status are normal, and the

BTS has obtained the configuration data, check if the Abis signaling

link configuration is correct.

Abis signaling link uses the IPOA mode, which requires

configuration of the following parameters: the PVC parameter (VPI

and VCI) of the Abis signaling link, the TCP/IP address (IP address,

subnet mask and TCP port ID.) We also need to make sure that the

PVC used by the Abis signaling link is different from that used by the

Abis service.

Содержание Airbridge cBTS3612






































































































Результаты поиска

Содержание Airbridge cBTS3612

Отзывы:

Похожие инструкции для Airbridge cBTS3612

Бренды по названию

Популярные бренды

Huawei Airbridge cBTS3612, Руководство по обслуживанию

Результаты поиска

Содержание Airbridge cBTS3612

Отзывы:

Похожие инструкции для Airbridge cBTS3612

Бренды по названию

Популярные бренды