HPE FlexNetwork 10500 SERIES Скачать руководство пользователя страница 310

Страница: 310 / 407

299

Configuration procedure

Before the configuration, make sure the device and the log host can reach each other. (Details not
shown.)

Configure the device:

# Enable the information center.

<Device> system-view

[Device] info-center enable

# Specify the log host 1.2.0.1/16, and specify

local5

as the logging facility.

[Device] info-center loghost 1.2.0.1 facility local5

# Disable log output to the log host.

[Device] info-center source default loghost deny

To avoid outputting unnecessary information, disable all modules from outputting log
information to the specified destination (

loghost

in this example) before you configure an

output rule.

# Configure an output rule to enable output to the log host FTP logs that have a severity level of
at least

informational

[Device] info-center source ftp loghost level informational

Configure the log host:

The following configurations were performed on Solaris. Other UNIX operating systems have
similar configurations.

Create a subdirectory named

Device

in the directory

/var/log/

, and create file

info.log

the

Device

directory to save logs of

Device

# mkdir /var/log/Device

# touch /var/log/Device/info.log

Edit the file

syslog.conf

in directory

/etc/

and add the following contents.

# Device configuration messages

local5.info /var/log/Device/info.log

In the above configuration,

local5

is the name of the logging facility used by the log host to

receive logs.

info

is the informational level. The Linux system will store the log information

with a severity level equal to or higher than

informational

to the file

/var/log/Device/info.log

NOTE:

Follow these guidelines while editing the file

/etc/syslog.conf

•

Comments must be on a separate line and must begin with a pound sign (#).

•

No redundant spaces are allowed after the file name.

•

The logging facility name and the severity level specified in the

/etc/syslog.conf

file must

be identical to those configured on the device by using the

info

center loghost

and

info-center source

commands. Otherwise, the log information might not be output to the

log host correctly.

Display the process ID of

syslogd

, kill the

syslogd

process, and then restart

syslogd

using the

-r

option to apply the new configuration.

Make sure the

syslogd

process is started with the

-r

option on a Linux log host.

# ps -ae | grep syslogd

147

# kill -9 147

# syslogd -r &

Содержание FlexNetwork 10500 SERIES
























































































































































































































































































































































































































Результаты поиска

Содержание FlexNetwork 10500 SERIES

Отзывы:

Похожие инструкции для FlexNetwork 10500 SERIES

Бренды по названию

Популярные бренды

HPE FlexNetwork 10500 SERIES, Руководство по настройке

Результаты поиска

Содержание FlexNetwork 10500 SERIES

Отзывы:

Похожие инструкции для FlexNetwork 10500 SERIES

Бренды по названию

Популярные бренды