HPC MOBILAIR M27 PE Скачать руководство пользователя страница 72 | Manualshive

Страница: 72 / 312

HPC MOBILAIR M27 PE Скачать руководство пользователя страница 72

5. Wait until the airend discharge temperature of +30 °C has been reached.
6. Check on the

remote contact thermometer that the airend discharge temperature of +30 °C has

been reached.

7.4.2 Starting assistance

The machine's electrical equipment is designed for starting at ambient temperatures as low

as −10 °C.

If the machine's starter battery is discharged, it can be started with the battery of another vehicle or

machine with combustion engine.

Material Jumper cables

Precondition The machine is disconnected from the towing vehicle and safely parked.

WARNING

Fire and explosion hazard.

Short-circuit currents caused by short-circuited battery. A damaged battery can catch fire or

explode.

Battery casing may crack and allow acidic fluid to spray out.
➤ Observe the instructions provided with the battery jumper cables.
➤ Do not connect the battery jumper cables to the negative pole of the discharged battery

or to the bodywork of the machine.

➤ Work with caution.

Fig. 15 Jumper cable connection diagram

a

Assisting vehicle battery (external donor

battery)

b

Engine battery (receiving battery)

1

Positive (+) terminal starting assistance

2

Positive (+) terminal of the machine battery

3

Bare metal point on the engine block

(earth)

4

Negative (-) terminal of assisting vehicle

battery

7

Initial Start-up

7.4

Low-temperature operation

60

Operating Manual Portable Rotary Screw Compressor
MOBILAIR M27 PE

No.: 9_9548 22 HCE

«
...
70
71
72
73
74
...
»

Содержание MOBILAIR M27 PE

























































































































































































































































































































Отзывы:

Нет отзывов