HPC MOBILAIR M27 PE Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 312

HPC MOBILAIR M27 PE Скачать руководство пользователя страница 13

1 Regarding this document

1.1 Using this document

The operating manual is a component of the product. It describes the machine as it was at the time

of first delivery after manufacture.
➤ Keep the operating manual in a safe place throughout the life of the machine.
➤ Supply any successive owner or user with this operating manual.
➤ Please insert any amendment or revision of the operating manual sent to you.
➤ Enter details from the machine nameplate and individual items of equipment in the table in

1.2 Further documents

Further documents included with this operating manual are:
■ Certificate of acceptance / operating instructions for the pressure vessel
■ Declaration of Conformity in accordance with the applicable directive
■ Chassis documentation (where applicable)

Missing documents can be requested from KAESER.
➤ Make sure all documents are complete and observe the instructions contained in them.
➤ Make sure you provide the data from the nameplate when ordering documents.

1.3 Copyright

This operating manual is protected by copyright. Any queries regarding the use or duplication of

this documentation should be referred to KAESER. Correct use of information will be fully suppor‐

ted.

1.4 Symbols and labels

➤ Please note the symbols and labels used in this document.

1.4.1 Warnings

Warnings indicate risks potentially resulting in personal injury, if the measures specified are not

taken.

Warning notices indicate three levels of danger identified by the corresponding signal word:

Signal word Meaning

Consequences of non-compliance

DANGER

Warns of an imminent danger

Will very likely result in death or severe injury

WARNING Warns of a potentially imminent dan‐

ger

May result in death or severe injury

CAUTION Warns of a potentially dangerous sit‐

uation

May result in a moderate physical injury

Tab. 1 Danger levels and their definition (personal injury)

1

Regarding this document

1.1

Using this document

No.: 9_9548 22 HCE

Operating Manual Portable Rotary Screw Compressor
MOBILAIR M27 PE

1

«
...
11
12
13
14
15
...
»

Содержание MOBILAIR M27 PE

























































































































































































































































































































Отзывы:

Нет отзывов