HP X5000 G2 Скачать руководство пользователя страница 9

Страница: 9 / 179

2 Installing the storage system

This chapter explains how to install the storage system hardware.

Verify the kit contents

Remove the contents, ensuring that you have all of the following components. If components are
missing, contact HP technical support.

Hardware

•

HP X5000 G2 Network Storage System

NOTE:

External disk enclosures are not included with the storage system, but up to four

D2600 or D2700 disk enclosures may be connected to the storage system.

•

Rail kit

•

Power cords

Media and documentation

•

HP X5000 G2 Network Storage System Quick Start Guide

•

HP ProLiant Essentials Integrated Lights-Out Advanced Pack

•

End User License Agreement

•

HP X5000 G2 System Recovery DVD

•

Certificate of Authenticity Card

•

Safety and Disposal Documentation CD

Locate and record the product number, serial number, and SAID number

Before you begin installation, locate and record the product number of the storage system, serial
number, and support contract service agreement ID (SAID) number.

The product number of the storage system and serial number are located in three places:

•

Top of the storage system

•

Back of the storage system on a pull-out tab

•

On the storage system shipping box

The SAID number is listed on your service contract agreement (see

“Obtaining the Service Agreement

ID” (page 54)

Unpack and rack the storage system hardware

WARNING!

The storage system enclosure is heavy. Always use at least two people to move the

storage system into the rack.

Verify the kit contents

Содержание X5000 G2




















































































































































































Результаты поиска

Содержание X5000 G2

Отзывы:

Бренды по названию

Популярные бренды

HP X5000 G2, Руководство администратора

Результаты поиска

Содержание X5000 G2

Отзывы:

Бренды по названию

Популярные бренды